WallVIEW PRO HD1 Installation and User Guide 341-661 Rev. D Page 2 of 14
UNPACKING:
Carefully remove all of the parts from the packaging and identify the following parts:
• One (1) - Sony EVI-HD1 High Definition PTZ Camera
• One (1) - Vaddio EZ Interface Module (EZIM)
• One (1) - Vaddio EZIM to HD Break-out Cable
• One (1) - Vaddio Quick-Connect PRO (1-RU Rack Mountable)
• One (1) - Vaddio Thin Profile PRO HD1 Wall Mount
• One (1) - Sony IR Remote Control
• One (1) - EZCamera Control Adapter 998-1001-232 (RJ-45 to DB-9F)
• One (1) - 36V PowerRite™ HD Power Supply with AC Cord Set
• One (1) - 2-position Phoenix Connector for IR
• Mounting Hardware
• Documentation
Vaddio Manual
Sony EVI-HD1 Manual
Optional Accessories: SD Break-out cable (for SD video configurations) - Part # 440-6204-000
TANDBERG Codec RJ-45 to DB-9 Adapter – Part # 998-1002-232
RS-232 and IR Adapter for Polycom 8000 & 7000 Series Codecs - Part # 998-1006-232
INSTALLATION
All WallVIEW products are specifically designed for installation on a vertical wall surface with Cat. 5 cable
connectivity for Power, Video and Control signaling. Installation is simplified in that no custom 8-Pin mini-din
cables or expensive S-Video plenum cables are needed and power outlets are not required near the camera
bracket. All cabling is routed to the head-end using Cat.5 cables. NOTE: All RJ-45 connectors need to be
terminated TIA/EIA 568B or A. The use of RJ-45 “EZ” connectors is not recommended.
Before Installing
• Locate the camera mounting position paying close attention to camera viewing angles, lighting conditions,
possible line of site obstructions, and checking for in-wall obstructions. Pick a location to optimize the
performance of the camera.
• Pre-wire all cabling from the camera location to the equipment head-end.
• The Thin Profile Wall Mount for the WallVIEW HD1 can be mounted directly to a 2-gang wall box or can
be mounted to the drywall using four dry wall anchors.
Wiring Diagram with HDX 9000 Series Codec:
Component Video (Y, Pb, Pr)
to HD codec or other device
36 VDC
Power Supply
IR Output
(See page 7)
WallVIEW HD1 with Camera,
Wall Mount and EZIM
Quick-Connect Pro
Up to 500’ (152.4m) of Cat. 5
for Power, Video and Control
Power Cat. 5
Video Cat. 5
Figure 2: The WallVIEW HD1 connected to an HDX 9000 series codec uses the standard RJ-45 to DB-9 adapter
supplied with the system and DB9 M-M gender changer (not supplied) for control between the camera and codec
breakout cable. IR is fed out of the Quick-Connect rack mount unit to the IR port on the back of the HDX 9000 series
codec for IR forwarding from the camera. The Power, Video and Control Cat. 5 cables can be run up to 500’
(152.4m) from the Quick-Connect box to the EZ Interface Module, which connects to the camera. See Step 9 for
additional information on HDX 9000 IR wiring.
RS-232 DB-9F Adapter with
Gender Changer
Y-C and Composite SD video outputs
(using optional SD break out cable – will
not output simultaneous HD and SD video)
Polycom HDCI
Adapter Cable
(20 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji